- Generated by
1.8.4
|
iLLD_TC29x
1.0
|
MULTICAN basic functionality. More...
#include "IfxMultican.h"Go to the source code of this file.
Functions | |
| boolean | IfxMultican_MsgObj_cancelSend (Ifx_CAN_MO *hwObj) |
| Cancel pending TX request by invalidating the request, only when frame transmission has not been started. More... | |
| void | IfxMultican_MsgObj_clearStatusFlag (Ifx_CAN_MO *hwObj, IfxMultican_MsgObjStatusFlag flag) |
| Clears the selected status flag of a message object. More... | |
| void | IfxMultican_MsgObj_deinit (Ifx_CAN *mcan, IfxMultican_MsgObjId msgObjId) |
| Reset the message object Append the message object to the end of idle list and reset message object registers. More... | |
| IfxMultican_MsgObjId | IfxMultican_MsgObj_getPendingId (Ifx_CAN *mcan, IfxMultican_MsgObjGroup msgObjGroup) |
| Get message object ID which has TX/RX pending flag from a message object group. More... | |
| IfxMultican_MsgObjStat | IfxMultican_MsgObj_getStatus (Ifx_CAN_MO *hwObj) |
| Get the message object status. More... | |
| boolean | IfxMultican_MsgObj_getStatusFlag (Ifx_CAN_MO *hwObj, IfxMultican_MsgObjStatusFlag flag) |
| Gets the status of the selected status flag of a message object. More... | |
| IfxMultican_Status | IfxMultican_MsgObj_readMessage (Ifx_CAN_MO *hwObj, IfxMultican_Message *msg) |
| Read a received CAN message. More... | |
| IfxMultican_Status | IfxMultican_MsgObj_sendMessage (Ifx_CAN_MO *hwObj, const IfxMultican_Message *msg) |
| Send a CAN message. More... | |
| void | IfxMultican_MsgObj_setFilter (Ifx_CAN_MO *hwObj, boolean extend, uint32 id, uint32 accMask) |
| Set message object filter. More... | |
| void | IfxMultican_MsgObj_setStatusFlag (Ifx_CAN_MO *hwObj, IfxMultican_MsgObjStatusFlag flag) |
| Sets the selected status flag of a message object. More... | |
| void | IfxMultican_Node_deinit (Ifx_CAN_N *hwNode) |
| Reset the CAN node. More... | |
| boolean | IfxMultican_Node_initRxPin (Ifx_CAN_N *hwNode, IfxMultican_Rxd_In *rxd, IfxPort_InputMode mode) |
| Select and initialise the CAN node receive pin. More... | |
| boolean | IfxMultican_Node_initTxPin (Ifx_CAN_N *hwNode, IfxMultican_Txd_Out *txd, IfxPort_OutputMode mode) |
| Select and initialise the CAN node transmit pin. More... | |
| IfxMultican_Status | IfxMultican_Node_recoverBusOff (Ifx_CAN_N *hwNode) |
| Recovers the CAN node from bus off. More... | |
| void | IfxMultican_Node_setBitTiming (Ifx_CAN_N *hwNode, float32 moduleFreq, uint32 baudrate, uint16 samplePoint, uint16 synchJumpWidth) |
| Calculates the best posible values and configures BTR register. More... | |
| void | IfxMultican_calcTimingFromBTR (float32 moduleFreq, uint32 btr, uint32 *baudrate, uint16 *samplePoint, uint16 *synchJumpWidth) |
| Returns the CAN node timing. More... | |
| void | IfxMultican_deinit (Ifx_CAN *mcan) |
| Reset the CAN module Reset and disable the CAN module, inclusive message object and node registers. More... | |
| volatile Ifx_SRC_SRCR * | IfxMultican_getSrcPointer (Ifx_CAN *mcan, IfxMultican_SrcId srcId) |
| Get the interrupt source register. More... | |
| void | IfxMultican_resetModule (Ifx_CAN *can) |
| resets Multican kernel More... | |
| void | IfxMultican_setListCommand (Ifx_CAN *mcan, uint32 cmd, uint32 arg2, uint32 arg1) |
| Execute a command from the command panel. More... | |
MULTICAN basic functionality.
IMPORTANT NOTICE
Infineon Technologies AG (Infineon) is supplying this file for use exclusively with Infineon's microcontroller products. This file can be freely distributed within development tools that are supporting such microcontroller products.
THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. INFINEON SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
Definition in file IfxMultican.c.
1.8.4